Aluminum-CNC

EVA GLASS LAMILATING MACHINE
( Using Direction )
CONTENT
Preface 2
1.safety 3
2.Transportation 8
3.Installation& pre-operation 10
4.Equipment intended purpose 14
5.Principles of glass laminating 14
6.Technical parameter 15
7.Main constructions 16
8.Operation method &Precautions 20
9.Laminating materials 31
10.Inspection, maintenance and repair 33
11.Regular failure and obviate method 34
12.Replace heating tube 35
13.Periodic inspection, Maintenance program 37
14. Wearing parts list 38
15. Electrical Schematic diagram 39
16. Vacuum Schematic diagram 42

EVA PAD cork pad for safety glazing glass separation

Silicone Vacuum Bag for EVALAM TEMPERED BEND lamination

Silicone Vacuum Bag for EVA Glass Laminating Machine&Autoclave

By Zac Lynn

+The combination of the silicone bag:

-Upper Silicone Sheet
-Down Silicone Sheet
-Edge Gear
-Silicone Tube

+Technical Parameters of Silicone Vacuum Bag

Tensile strength
Tearing strength
Hardness
Breaking extensibility

Color
Pattern Temperature Resistance
6.5(Mpa) 26(N/mm) 55±5(Shore A) 450% Transparent
One smooth
One cloth grain 230 °C

+Description:
-Product Purpose: used for glass vacuum laminating machines to make
safety laminated glass with EVA FILM INTERLAYER, or for making privacy glass, switchable glass with PDLC FILM and EVA FILM
-Product features: heat-resistant, aging-resistance , anti-corrosive,environment-friendly, Long-use life, good resistance

+Product specification:
1) common thickness: 3mm
2) maximum width:3800mm with no joint
3) any length
4) common color: transparent,red, and any color available
5)Customization is available as customers require

+Notes When Using the Silicone Vacuum Bag

-Please edging the glass before laminating, which can prohibit the sharp glass edges of the glass cut the silicone bag.
-Use tape to seal the pre-laminated glass to reduce the EVA leaking from the laminated glass.
-Use some papers/fabric to cover the silicone bag to separate the EVA from the silicone bag
-Put some wires net on the vacuum hole to help vacuuming.
-When not laminating , put the silicone bag out of the hot oven.

+ Procedure of Ordering:
(1)Be ware of the kind of silicone you need: for EVA glass lamination or for solar encapsulation.

(2)If you need silicone vacuum bag for EVA glass lamination, please offer the internal size and external size of the silicone bag.

(3)If you need silicone rubber sheet for solar encapsulation, please offer the thickness, width, length.

Cork Pad packing for EVA safety laminated glass

GREEN TAPE for EVALAM interlayer film lamination

Thermal Laminated Glass Edges Trimmers, for EVA, PVB, SGP, TPU

EVA Thermal Cutter
to clean laminated glass edges overflowed remains of EVA, PVB, SGP etc.
Technical Data:
CE Standard: AC 230V/50Hz
US Standard: AC 120V/60HZ
Power: MAX 90W
Temperature of Blades: Up to 500℃ in seconds

Preparation:
A-Select a Thermal Cutter blade corresponding to the cutting use.
B-Loosen the knurled nut when device is cold.
C-Insert each leg of the blade and tighten the knurled nuts. Make sure that the blade and the cutting head have optimal contact. If both legs of the blade are not properly installed, the unit will not heat up.
D-Power on.

Cutting:
A-Actuate switch, the indicator light and the blade will heat up.
B-Avoid direct short circuit between cutting heads.
C-Do not use metallic rulers for guiding the blade.
D-Clean cutting heads with enclosed wire brush.
E-Please make sure the blade is connected to the cutting material before blade heats up.

Caution:
A-Always operate the Thermal Cutter in well ventilated space.
B-Never burn off the excess residue on the Thermal Cutter blade. The blades will over heated and be warped.
C-Only operate Thermal Cutter when it is in contact with the insulation board
D-Keep hot blades away from skin, clothing and other flammable materials.
E-Allow blades to cool before handling. Thermal Cutter may cause injury or burns to exposed surfaces.
F-The Thermal cutter is working intermittently, that means If the temperature inside the tool is too high, the unit will get hot and the internal thermal protectors will turn off automatically, after it cool, the Thermal Cutter will operate again.